CLAAS Scorpion 756

FOLLOWERS

936

LIKES

1:17 scale model of CLAAS Scorpion 756 telehandler.

Designed and built by Eric Trax, instructions made by me.
Visit his Facebook page for more great agriculture models:

https://www.facebook.com/Eric-Trax-167670136660216/

Model is completely motorized, with 5 motors (single servo motor, single L motor and three M motors) and controlled by three IR receivers (you need at least one IR remote).

Video showing it in action:


Parts list in Rebrickable, Bricklink XML, Brickstore and png versions can be found here: https://bricksafe.com/pages/M_longer/misc/claas-scorpion

Or by clicking here:
Rebrickable CSV
Bricklink XML
Brickstore BSX

Sticker sheet in PDF format can be downloaded by clicking here:
https://bricksafe.com/files/M_longer/misc/claas-scorpion/Claas-Scorpion-756-stickers.pdf




These parts lists include a 3L long 3mm rigid hose, more about its usage below:

Before you buy these instructions, please read the following really carefully.

– This model is not recommended for persons under 16 years of age and those with little experience in building more complex models.

- This model is built on 4x4x4 chassis, which means that all four wheels are steered and driven. Each wheel use CV Joint, and we really reccomend cuting some 3mm rigid hose to 0.5 stud/4mm slices and placing them one by one inside each of the joint.
The reason for that little cheat is related to overall length of drive axles (3L) and free space inside the CV joint (0.5 stud). That half stud might cause the 3L axle to slide out from the differential. In other words – you either need to cut that hose to small slices (more legal-ish attempt), or you can sacrifice four 4L axles and reduce their length by half stud and become an outlaw ;)






- If you have built one of our tractors (New Holland TM 140 or Fendt Favorit 514C) you are quite familiar with Eric’s building style and not-so-friendly routing of electric wires trough model(s). But this telehandler raises the bar even more.

– The assembly is likely to take quite a bit of your time. It might be the reason for nervous breakdowns when it will come to routing the electric wires around the chassis and, especially under the linear actuator. Model is extremely dense and there's only a little space for all those wires inside. There’s really tight space under the cab, and all wires must be routed very tightly in given space:



- All wires are colour coded:






- There are three IR receivers, colour coded to Lime, Light Blue and Tan. Blue one is connected to the battery, but remaining two uses not so well known ability of IR receivers to be powered from outputs of other receivers. Both Tan and Lime are connected to Light Blue’s second output.

- To comfortly play with this model, I reccomend to use at least two IR Remotes.

- Please remember that each receiver must be set to different channel.



- There are three motors located in the telescopic arm (Brown, Green and Orange connected to  50cm extension wire), and connectors of all three can be connected to the IR receivers only after placing the whole arm on the chassis. It also means that for few steps (before placing the floor of the cab) Tan receiver will be not connected to anything (except the wire of course).

- Wire from Orange motor has to be folded in half and placed inside the arm, allowing it to unfold with arm moving forward

- Orange and Brown wires must go trough linear actuator’s bracket (yes, I know, blame Eric for that :D ). I strongly advise to test if everyting works (for example - one of the wires, if placed not correctly can rub on gears driving the actuator) before adding those 5L axles on page 95

- Remaining part of the Orange wire must be squeezed in the chassis, allowing the actuator to fit into place after lowering arm to ground position

-  Due to way it was built (and assembled) there are no locks on the telescopic arm, which means that model must be controlled with care

- Eric has built this model with using Dark Red wheels, they are quite rare, so model from instructions is using Light Bluish Gray ones.

– Before purchasing, please review the list of required parts. Most of them are widely available, but some lime parts are not so popular.

Sample pages from instructions:



Buy this MOC

Want to buy this MOC to build? You'll need to buy the parts and the building instructions using the tabs below.
Login to hide ads!

MOC-35607

Name CLAAS Scorpion 756
Designer M_longer
Designed 2020
Inventory 1408 parts
Theme Technic > Model > Farm
Old Trafford
Already have some of the parts? Use the Build this MOC page to only show the parts you are missing.
Create an account to change the default filters used.

Waiting for Inventory to load

Instructions:
PDF - Computer Images
Cost:

Please Log In

Sorry, but you need to be logged in to buy these instructions so that you can download them again at any time. Login or quickly signup using the form below.
Help Guide - BI File Types